Pentair Sta-Rite JP Series Composite 4" Submersible Pumps

Main Content Starts Here

Pentair Sta-Rite JP Series Composite 4" Submersible Pumps

Precision-engineered, corrosion-resistant composite pumps deliver efficient, dependable performance even in rough, aggressive water

KEY FEATURES

  • SignaSeal staging system incorporates a harder-than-sand ceramic wear surface and a floating impeller design - which together literally pulverize sand and small debris. This proven feature reduces lock-ups, dry-runs, and abrasive wear.
  • Floating Stage Design is engineered to transmit forces away from the motor bearing and through the pump housing. This reduces premature wear and misalignment.
  • Fully-Enclosed Shaft Bearing creates a pressure zone that prevents sand & water from entering. Eliminates wear and misalignment.
  • Wear Ring forms a seal between impeller hub and suction cap for low friction and no unwanted recirculation of water.
  • Corrosion-resistant fiberglass reinforced thermoplastic intake & discharge for durability in aggressive water.
  • Large octagon wrench area for ease of installation.

WARRANTY

1-year limited warranty

Find out where to purchase online or in a retail location near you.
Where to Buy

Upstaged for Higher Performance

The Signature 2000® 4" submersible pump design has been delivering dependable performance since 1990. Our floating stage design continues to handle even the most aggressive water with our SignaSeal™ system that breaks down debris and reduces locking. Now we’re going further by upstaging and adding additional features to the 4" inch submersible pumps you’ve grown to trust and rely on every day!

What Does This Mean For You?

Better Performance
With increased staging across much of our 1/2 to 1-1/2HP pumps, you'll enjoy even greater performance receiving more depth and/or more flow than before.

Beat the Competition
Our increased staging gives you an average of 20% higher performance than competitive pumps at like horsepower and rated flow. We've even developed a tool to show you how our 4" submersible pumps compare to the top competitors. Visit www.pumps.com/curveenvy.html to compare your pump!

The New Standard in Reliability
Experience the new standard with our redesigned JP series that includes a stronger discharge and added spring-loaded check valve.

Performance Curves

PerformanceCurves_4" Submersible, Composite Materials, 1/2 thru 1-1/2 HP, 2- and 3-Wire, 10 - 30 GPM, 1-1/4" Discharge

Specifications

HORSEPOWER:  Available in 1/2 thru 1-1/2 HP
PERFORMANCE SERIES:  10, 15, 20, and 30 GPM Series Available
NUMBER OF STAGES:  5 - 14 (model dependent)
VOLTAGE:  115v (1/2 HP only) or 230v, 60 Hz
NUMBER OF WIRES:  2-or 3-wires plus ground (model dependent)
MATERIALS:  Corrosion Resistant fiberglass reinforced thermoplastic
SHELL:  Stainless steel
DIAMETER:  3-3/4"
LENGTH:  22-1/4" to 34-3/4" (model dependent)
WEIGHT:  27" to 43"
DISCHARGE:  Fiberglass-Reinforced Thermoplastic, 1-1/4" NPT
DISCHARGE BEARING:  Self-Lubricating Nylatron®
IMPELLERS:  Acetal
DIFFUSERS:  Polycarbonate
SUCTION CAPS:  Polycarbonate with Stainless Steel Insert
THRUST PADS:  Proprietary spec
SHAFT END COUPLING:  Stainless Steel
INTAKE:  Fiberglass-Reinforced Thermoplastic
INTAKE SCREEN:  Polypropylene
CABLE GUARD:  Stainless steel
CHECK VALVE:  Acetal

Nylatron® is a registered trademark of Quadrant Engineering Plastic Products

Back to top of page